Ram 1500/2500/3500: Soft-Keys - Audio
After pressing the "Audio" soft-key the following settings will be available:
- Balance/Fade
When in this display you may adjust the Balance and Fade settings.
- Equalizer
When in this display you may adjust the Bass, Mid and Treble settings. Adjust the settings with the "+" and "-" soft-keys or by selecting any point on the scale between the "+" and "-" soft-keys. Then touch the back arrow soft-key.
NOTE: Bass/Mid/Treble allow you to simply slide your finger up or down to change the setting as well as touch directly on the desired setting.
- Speed Adjusted Volume
This feature increases or decreases volume relative to vehicle speed. To change the Speed Adjusted Volume touch the "Off," "1," "2" or "3" soft-key. Then touch the back arrow soft-key.
- Surround Sound - If Equipped
This feature provides simulated surround sound mode.
To make your selection, touch the "Surround Sound" soft-key, select On or Off followed by pressing the back arrow soft-key.
- AUX Volume Match - If Equipped
This feature provides the ability to tune the audio level for portable devices connected through the AUX input.
To make your selection, touch the "AUX Volume Match" soft-key, select On or Off followed by pressing the back arrow soft-key.
- Loudness - If Equipped
The Radio automatically turns on when vehicle is in run or will recall whether it was on or off at last ignition off.
To make your selection, touch the "Loudness" soft-key, select On or Off followed by pressing the back arrow soft-key.
Trailer Brake
- Trailer Select
When this feature is selected, the Trailer Type can be selected between "Trailer 1," "Trailer 2," "Trailer 3" and "Trailer 4." To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
- Trailer Brake Type
When this feature is selected, the Trailer Brake Type can be changed between "Light Electric," "Heavy Electric," "Light EOH" and "Heavy EOH.". To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. Refer to "Integrated Trailer Brake Module" in "Starting And Operating."
- Trailer Name
When this feature is selected, the Trailer name can be selected from 16 names. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
READ NEXT:
Soft-Keys - Phone/Bluetooth
After touching the "Phone/Bluetooth" soft-key the
following settings will be available:
Paired Devices
This feature shows which phones are paired to the
Phone/Bluetooth system. For further informat
Uconnect Radios - If Equipped
For detailed information about your Uconnect radio,
refer to your Uconnect Supplement Manual.
iPod/USB/MP3 Control - If Equipped
Located in the lower section of the front integrated center
stack, in f
Steering Wheel Audio Controls - If Equipped
The remote sound system controls are located on the back
surface of the steering wheel. Reach behind the wheel to
access the switches.
Remote Sound System Controls (Back View Of Steering
Wheel)
The r
SEE MORE:
Wheel And Tire Torque Specifications
Proper lug nut/bolt torque is very important to ensure
that the wheel is properly mounted to the vehicle. Any
time a wheel has been removed and reinstalled on the
vehicle the lug nuts/bolts should be torqued using a
properly calibrated torque wrench.
Torque Specifications
**Use only Chrysler recomm
Enabling And Disabling ParkSense
ParkSense can be enabled and disabled with the
ParkSense switch.
When the ParkSense switch is
pressed to disable
the system, the instrument cluster will
display the "PARKSENSE OFF" message for
approximately five seconds. Refer to "Electronic
Vehicle Information Center (EVIC)" in "Understanding
Your
